Memuat
Memuat
A women's hooded parka with a fur trim, a fishtail back, flap patch pockets and slim trousers.
0 views
A winter outfit for the Mia avatar. The loose olive canvas parka has a two-piece hood with a fur trim, a back hem curving down (fishtail), a front placket flap, two flap patch pockets and rib cuffs with tabs; below are slim black denim trousers. The parka sits on a layer above the trousers.


Four-piece trousers with little ease are sewn at the side, inseam and crotch, then given front and back waistbands.
Two fronts, a back and two sleeves are made from basic blocks sized to Mia with 200 mm of ease. The back hem gets a curve point so it dips at the centre.
Two hood halves are sewn along the centre line, then to the neckline; a two-segment fur strip is sewn along the face edge of the hood.
Shorter rib cuffs are sewn to the sleeve ends, then small tabs are patched near the sleeve ends.
A placket flap is patched along the left front edge; two patch pockets and their flaps are added on the lower fronts on higher layers.
Each piece is placed on an avatar arrangement point and given a layer number. The simulation runs in two phases: first without gravity so the seams close, then with normal gravity.
Fabrics
Olive canvas for the parka, cream faux fur (a stock preset) for the hood trim, cream rib (our own texture) for the cuffs and black denim (our own texture) for the trousers.
Avatar
The stock CLO female avatar (Mia). Pattern sizes are derived from the avatar body: bust 870 mm, waist 615 mm, hip 955 mm.
Note: The fur trim uses the stock faux-fur preset on a fabric strip (not strand fur), and the parka has no working zipper. The patterns were built from a millimetre-based pattern library in Marvelous Designer, and the .zprj file was then opened in CLO3D 2025. Buttons, buckles and zippers are small sewn fabric pieces, not 3D trims. The avatar is a stock CLO avatar and the fabric textures are our own. The patterns are not graded and are not prepared for production. The images on this page are captures of the CLO3D 2025 3D window after opening the .zprj file (not final renders).
The Parka_Bertudung.zprj file: fully open in CLO3D and Marvelous Designer (2D patterns, seams, fabrics); Our own PNG fabric textures: rib_krem.png, denim_hitam.png, netral.png; Preview images of the garment (front, back, side, three-quarter); READ-ME: the list of pattern pieces, fabrics and how to open the file; Step-by-step PDF guide (coming soon, sent once finished); Video tutorial on making the garment (coming soon); Requires CLO3D or Marvelous Designer (made with the 2025 release; use the same or a newer release).
The .zprj file opens in CLO3D and in Marvelous Designer (made with the 2025 release; use the same or a newer release). The 2D patterns, seams and fabrics are all open and editable. The patterns were built in Marvelous Designer from a millimetre-based pattern library, then the file was opened in CLO3D 2025.
No. Buttons, buckles and zippers are small sewn fabric pieces, and some yoke, quilting and pleat lines are internal style lines rather than separate pieces. You can replace them with real CLO3D trims yourself after opening the file.
Yes. The patterns are sized to the stock Mia avatar and are not graded, but every 2D pattern is open, so you can edit the pieces, swap fabrics and replace the textures, then simulate again. If you would like us to adapt the garment for you, message us on WhatsApp.
The project costs US$24. Use the "Buy via WhatsApp" button on this page; the project files are sent over WhatsApp after payment is confirmed.
Found a problem or have a suggestion for this project? Tell us on WhatsApp
Back to CLO3D portfolio